Report on the Yildiz Magnet Motor Demo
Wed Apr 10, 2013 7:48 am (PDT) . Posted by:
"Sterling Allan" sterlingda888
http://pesn.com/2013/04/10/9602291_Yildiz_magnet-motor_runs_5.5-hours_at_Geneva_demo_day_1/
Report on the Yildiz Magnet Motor Demo in Geneva, April 10, 2013; 4:30
pm GMT.
by Sterling D. Allan
Pure Energy Systems News
PESWiki (which is where
http://YildizDemo.com forwards) seems to be down presently, so I'm
sending this report out by email to our mailing list. I've sent a notice
to our server provider to inform them of the outage. Hopefully it will
be repaired soon. Meanwhile, the live stream can be found at
http://www.justin.tv/pesnetwork
We've had a lot of internet connectivity problems here at Palexpo
[low-quality, expensive internet service], so most of the morning the
feed was not going out. That is in process of being resolved with a Cat5
connection with 1 Mbs upload speed (cost $432 to set that up for the
remaining 4 days). I forgot that internet is not nearly as robust in
Europe as it is in the US, and I expected that the Expo wifi would be
adequate.
This morning, when Mr. Yildiz went to start the motor at around 10:05
am, shortly after the conference opened, it didn't start. He pulled it
into a closet at their booth for about 20 minutes, then emerged. Then he
started it by the way you've seen on the web.
The motor ran from 10:28 am to 2:50 pm GMT, nearly 5.5 hours.
It started at 2600 rpm, then went up in speed to 2673, then down and up
that range for about 3 hours.
Then, a magnet was "loose", and the motor began to slow. Then, he said
that the magnet alignment malfunction began to cascade so that 3 were
out of line. By 2:21, the speed was 2064. A noise could be heard from
the motor, so he turned it off.
Then, at 3:10 pm, he turned it on again, and it went to 1930 rpm, then
began dropping rapidly
1734 rpm at 3:12
1522 at 3:15
He stopped it at 3:16 pm
The temperature was around 23 degrees on the front and back bearings,
just 1 degree C above room temp: 22 C
So presently, the motor is off.
He plans to work on it this evening, then run it again tomorrow,
hopefully all day (and hopefully through the night too).
Assistant professor Duarte is present. Last night he openly stated to
the group of about 12 people assembled in a villa in France, that he has
seen inside the motor and there are no batteries in there.
Also, yesterday, Yildiz demonstrated an effect in which copper coins
(which normally are not attracted to magnets) stuck to the outside of
the magnet motor, while silver-colored coins (which normally are
attracted to magnets) drop off the outside of the same motor body -- the
opposite of what you would expect. This illustrates that there is
something very unusual going on.
Duarte also points out that with magnets rotating around in vicinity of
aluminum that there should be eddy currents and heat produced; but that
is not observed in this set-up. (Remember, he saw inside and saw the
magnets.)
The booth has been busy with observers all day up until about 4 pm. Now
that the motor is stopped, the walk-by interest has dropped
significantly, as could be understood.
He hasn't run the smaller motor at all today yet. When I get free here,
I hope to ask him to run it. I want to burn my hand on the shaft trying
to stop it with bare hands. That motor has no control, so it has to be
stopped by gloves on the shaft to prevent it from speeding to
destruction.
Rene and his film crew have been here all day, including for about an
hour after the motor was stopped.
I had to fork out $34 SF (close to USD) for lunch. Crazy expensive here.
The airport next door will be much cheaper, and you all know how
expensive airport food is.
Having a great time. Thanks for enabling me to come here. I think it
will be well worth the trip.
I've shot a lot of photos and video, and will be getting some of that up
soon, hopefully.
| Sterling D. Allan,
| New Energy Systems Trust (NEST), Founder
| http://www.EnergyNEST.org
| (Pure Energy Systems) PES Network, Inc., CEO
| http://PESWiki.com
|
| "The best news and directory service on the net
| regarding cutting edge energy technologies."
|
| Profile: http://SterlingDAllan.com
| Phone: +1-801-407-1292 (mountain time)
| Ephraim, Utah, USA
www.pureenergysystems.com
PES Network, Inc.
Copyright © 2003 - 2013
http://groups.yahoo.com/group/FE_updates/message/2152;_ylc=X3oDMTJxM2RmcTN0BF9TAzk3MzU5NzE1BGdycElkAzc5MDQyNTQEZ3Jwc3BJZAMxNzA1MDgzMjY5BG1zZ0lkAzIxNTIEc2VjA2Rtc2cEc2xrA3Ztc2cEc3RpbWUDMTM2NTYxMzc1MQ--
|